Поиск:
 

The original manufacturer can not achieve the accuracy of 1.0μm hydraulic pressure control valves, b

RU-1000 Рейтинг
Поделитесь страницей в Социальных сетях

Hannelore is from Germany and has been engaged in procurement for many years. Their company is going to launch a new hydraulic injection molding machine, which uses hydraulic pressure control valves. He selected a hydraulic pressure control valve manufacturer who has been cooperating for 5 years to make samples, and emphasized that the geometric accuracy of the valve spool and valve sleeve needs to be within 1μm. The manufacturer said that he might not be able to achieve it, but Hannelore believed in the sample capacity of the manufacturer because there were similar cases before. After 45 days, the hydraulic pressure control valve was installed with the equipment and began to test run. However, the movement speed of the actuator of the equipment was unstable. The engineer judged that the hydraulic pressure control valve was not up to the standard. The actual problem was that the geometric accuracy of the valve spool and valve sleeve was not up to the standard, which led to the inflexibility of the hydraulic pressure control valves. The original manufacturer has surrendered, and it will be a waste of time to retest. Hannelore contacted more than 10 hydraulic valve manufacturers. They either have no reply, or said that they were only 80% confident. Hannelore had no time to bet on this 80% confidence, because the exhibition time was approaching. At this time, Hannelore was extremely worried.

Hannelore found AAK Hydraulic Valve on Google, leaving a message: how much can the geometric accuracy of the valve spool and valve sleeve of the hydraulic pressure control valve be controlled. I replied directly, within 1.0μm, no problem. Hannelore sent the drawing of hydraulic pressure control valve and asked for AAK samples. After 40 days, AAK hydraulic pressure control valve samples were sent. After 10 days, Hannelore advised that the geometric accuracy of the valve spool and valve sleeve of each sample of AAK did not exceed 0.8μm. The prototype passed their test run is already on the way to the exhibition hall. Hannelore\'s depressed mood was finally released. I told him to have a drink in the evening and then just wait patiently for the good news of the exhibition.

Last week, Hannelore told us that the exhibition effect was good. He ordered 800 hydraulic pressure control valves first, and emphasized that the delivery time should be on time and the quality should be the same as the trial order. I joked that these are the lowest level commitments in AAK. AAK hydraulic pressure control valves broke his concerns completely with 3 points:

Swiss high-precision honing machine, the geometric accuracy of valve spool and valve sleeve can be controlled within 0.8μm. With this precision foundation, there is no need to worry about the optimal range of the fitting clearance between the valve spool and the valve sleeve.

The Mahr cylindricity meter imported from Germany, through EasyForm software, the measurement results can be obtained accurately and quickly. With the help of the software, the workpieces can be quickly adjusted and aligned to improve the measurement efficiency and make the accuracy of each gap consistent.

AAK is the hydraulic valve supplier of 7 world top 500 enterprises, its service has been verified for a long time, both in terms of delivery date and manufacturing quality.

AAK hydraulic pressure control valves, high precision, long life, you can also try it!

AAK HYDRAULIC VALVES (327) 2022-08-23

Вас также могут заинтересовать

The original factory can not achieve the hydraulic relief valve with IT7~4 hole accuracy, and AAK wi

Chernychevsky is from a Russian company specializing in medical hydraulic equipment. Last week, I received an urgent order from him, urgently needing 30 hydraulic pilot operated relief valves. He spec

AAK has no competitors in the hydraulic pressure control valves that can withstand 450bar high press

AAK hydraulic pressure control valves with pressure resistance above 450bar and high frequency use for more than 1 year without wear. After a year of trial, Romero reordered 800 hydraulic pressure con

The original hydraulic valve manufacturer cannot meet the accuracy of valve hole 1.0μm for hydraulic

In March this year, Danielisadora, a Brazilian customer, sent us an inquiry, urgently needing 20 non-standard customized hydraulic flow control valves with an accuracy of 1.0μm valve hole, which is re

The original hydraulic valve manufacturer can not solve the problem of the hydraulic relief valves f

Bauer has been working in K & G company in Brazil for 6 years. His boss always trusts his work. Bauer and AAK have cooperated for 2 years. Two years ago, the marketing of a hydraulic windlass deve

The original manufacturer shifted the responsibility of the Hydraulic Pressure Control Valve, AAK to

Lateef, from Sweden, has been engaged in the procurement of hydraulic valves for 3 years and has been quite successful. Last year, however, he stumbled due to a hydraulic pressure control valve used i
Внимание!
Информация по The original manufacturer can not achieve the accuracy of 1.0μm hydraulic pressure control valves, b предоставлена компанией-поставщиком AAK INDUSTRY CO., LTD. Для того, чтобы получить дополнительную информацию, узнать актуальную цену или условия постаки, нажмите ссылку «Отправить сообщение».
Контакты компании
Страна
Китай
Город
NINGBO
Сделать запрос
Введите свое имя
Укажите свой Email
Напишите ваш вопрос
Подтвердите согласие